AcQuisition Technology Quad M-module Carrier i4000 Guide de l'utilisateur Page 56
- Page / 134
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
40 007-4522-003
2: Connecting to a Host and Powering On and Off
Other modules in the storage system also have LEDs, which are described in “Using
Storage System LEDs for Troubleshooting” on page 78.
Connecting the Power Cords and Powering On the 2 Gb TP9100 Rack
The rack requires 220 V and is shipped with a country-specific power cord for each
power distribution unit (PDU) that the rack contains. Each power supply of each
enclosure in the rack is cabled to the rack PDU on the appropriate side; Figure 2-3 shows
an example.
The PDU has double-pole circuit breakers and can be connected to either a
phase-to-neutral power source or to a phase-to-phase power source.
Warning: The power distribution units (PDUs) at the sides in the rear of the rack
contain hazardous voltages. Do not open the PDUs under any circumstances.
A qualified SGI system support engineer (SSE) will set up the rack and cable it to power.
The information in this section is provided for reference and safety reasons only.
Additional rackmountable enclosures that you order after your rack is set up are shipped
with two IEC 320 power cords for cabling to the rack PDUs. Qualified SGI SSEs will
install and cable the enclosures in the rack.
Warning: The rack PDUs must be connected only to power sources that have a safe
electrical earth connection. For safety reasons, this earth connection must be in place
at all times.
- Storage System User’s Guide 1
- Record of Revision 3
- Contents 5
- 007-4522-003 vii 7
- About This Guide 13
- Related Publications 14
- Product Support 15
- Reader Comments 16
- 1. Storage System Overview 17
- RAID Configuration Features 18
- SAN Mapping 256 19
- Drive Sizing Algorithm 19
- 4 007-4522-003 20
- 1: Storage System Overview 20
- JBOD Configuration Features 21
- Availability Features 21
- Supported Platforms 21
- Storage System Enclosure 22
- 007-4522-003 7 23
- Enclosure Components 24
- • Dummy drive carrier modules 25
- Operators (Ops) Panel 27
- PSU/Cooling Module 28
- 007-4522-003 13 29
- Figure 1-7 PSU/Cooling Module 29
- RAID LRC I/O Modules 30
- Host 1Host 0 31
- RAID Loopback LRC I/O Modules 32
- JBOD LRC I/O Module 34
- Drive Carrier Module 35
- Drive Carrier Handle 36
- Anti-tamper lock 37
- Unlocked 37
- Indicator 37
- Enclosure Bay Numbering 38
- Tower Enclosure Bay Numbering 40
- Storage System Rack 42
- 007-4522-003 27 43
- 28 007-4522-003 44
- 007-4522-003 29 45
- 007-4522-003 31 47
- Storage System Tower 48
- 007-4522-003 33 49
- 34 007-4522-003 50
- Connecting to a Host 51
- 36 007-4522-003 52
- Grounding Issues 53
- 38 007-4522-003 54
- System/ESI fault LED 55
- Power on LED 55
- PSU/cooling/temperature 55
- Alarm mute switch 55
- 40 007-4522-003 56
- Powering On the Rack 58
- 007-4522-003 43 59
- ON shows 59
- I”=on, “O”=off) 59
- Powering Off 60
- 007-4522-003 45 61
- 46 007-4522-003 62
- 007-4522-003 47 63
- Configuration on Disk (COD) 64
- Drive Roaming 65
- Data Caching 66
- 007-4522-003 51 67
- RAID Disk Topologies 68
- This configuration: 69
- 4. Using the RAID Controller 75
- RAID Levels 76
- 007-4522-003 61 77
- Array Condition Meaning 79
- RAID Levels and Availability 80
- Disk Topologies 81
- RAID (base) enclosure 83
- First expansion enclosure 83
- (Enclosure ID 1) 83
- (Enclosure ID 2) 83
- System Drives 84
- Drive State Reporting 85
- State Description 86
- Automatic Rebuild 87
- 72 007-4522-003 88
- 4: Using the RAID Controller 88
- 007-4522-003 73 89
- 5. Troubleshooting 91
- RAID Guidelines 92
- 007-4522-003 77 93
- 78 007-4522-003 94
- 7 address ranges 97
- 82 007-4522-003 98
- PSU good LED 100
- DC ouput fail LED 100
- AC input fail LED 100
- Fan fail LED 100
- RAID LRC I/O Module LEDs 101
- Expansion 103
- JBOD LRC I/O Module LEDs 105
- Drive Carrier Module LEDs 106
- present 107
- Thermal Control 108
- Using Test Mode 109
- 94 007-4522-003 110
- 5: Troubleshooting 110
- Adding a Drive Carrier Module 111
- Torx screwdriver 112
- 007-4522-003 99 115
- A. Technical Specifications 119
- Component Weight 120
- Specification Value 120
- Environmental Requirements 121
- Power Requirements 122
- LRC I/O Module Specifications 123
- Factor Requirement 124
- B. Regulatory Information 125
- Attention 126
- VCCI Class 1 Statement 126
- Class A Warning for Taiwan 127
- 114 007-4522-003 130
- 116 007-4522-003 132
- 118 007-4522-003 134
Produits connexes et manuels pour Mise en réseau AcQuisition Technology Quad M-module Carrier i4000
(20 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.240 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels