AcQuisition Technology Quad M-module Carrier i4000 Guide de l'utilisateur Page 111
- Page / 134
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
007-4522-003 95
Chapter 6
6. Installing and Replacing Drive Carrier Modules
This chapter explains how to install a new drive carrier or replace an existing one in the
following sections:
• “Adding a Drive Carrier Module” on page 95
• “Replacing a Drive Carrier Module” on page 98
Note: The RAID controller supports hot-swap disk drive replacement while the storage
system is online: depending on the RAID level, a disk drive can be disconnected,
removed, or replaced with another disk drive without taking the storage system offline.
Caution: Observe all ESD precautions when handling modules and components. Avoid
contact with backplane components and module connectors. Failure to observe ESD
precautions could damage the equipment.
Adding a Drive Carrier Module
Note the following:
• All disk drive bays must be filled with either a drive carrier module or a dummy
drive; no bay should be left completely empty.
• The drives in bays 1/1 and 4/4 are required for enclosure management; these bays
must always be occupied.
To add a new disk drive module to the storage system, follow these steps:
1. Ensure that you have enough drive carrier modules and dummy modules to occupy
all bays.
2. Carefully open the bag containing the drive carrier module.
!
- Storage System User’s Guide 1
- Record of Revision 3
- Contents 5
- 007-4522-003 vii 7
- About This Guide 13
- Related Publications 14
- Product Support 15
- Reader Comments 16
- 1. Storage System Overview 17
- RAID Configuration Features 18
- SAN Mapping 256 19
- Drive Sizing Algorithm 19
- 4 007-4522-003 20
- 1: Storage System Overview 20
- JBOD Configuration Features 21
- Availability Features 21
- Supported Platforms 21
- Storage System Enclosure 22
- 007-4522-003 7 23
- Enclosure Components 24
- • Dummy drive carrier modules 25
- Operators (Ops) Panel 27
- PSU/Cooling Module 28
- 007-4522-003 13 29
- Figure 1-7 PSU/Cooling Module 29
- RAID LRC I/O Modules 30
- Host 1Host 0 31
- RAID Loopback LRC I/O Modules 32
- JBOD LRC I/O Module 34
- Drive Carrier Module 35
- Drive Carrier Handle 36
- Anti-tamper lock 37
- Unlocked 37
- Indicator 37
- Enclosure Bay Numbering 38
- Tower Enclosure Bay Numbering 40
- Storage System Rack 42
- 007-4522-003 27 43
- 28 007-4522-003 44
- 007-4522-003 29 45
- 007-4522-003 31 47
- Storage System Tower 48
- 007-4522-003 33 49
- 34 007-4522-003 50
- Connecting to a Host 51
- 36 007-4522-003 52
- Grounding Issues 53
- 38 007-4522-003 54
- System/ESI fault LED 55
- Power on LED 55
- PSU/cooling/temperature 55
- Alarm mute switch 55
- 40 007-4522-003 56
- Powering On the Rack 58
- 007-4522-003 43 59
- ON shows 59
- I”=on, “O”=off) 59
- Powering Off 60
- 007-4522-003 45 61
- 46 007-4522-003 62
- 007-4522-003 47 63
- Configuration on Disk (COD) 64
- Drive Roaming 65
- Data Caching 66
- 007-4522-003 51 67
- RAID Disk Topologies 68
- This configuration: 69
- 4. Using the RAID Controller 75
- RAID Levels 76
- 007-4522-003 61 77
- Array Condition Meaning 79
- RAID Levels and Availability 80
- Disk Topologies 81
- RAID (base) enclosure 83
- First expansion enclosure 83
- (Enclosure ID 1) 83
- (Enclosure ID 2) 83
- System Drives 84
- Drive State Reporting 85
- State Description 86
- Automatic Rebuild 87
- 72 007-4522-003 88
- 4: Using the RAID Controller 88
- 007-4522-003 73 89
- 5. Troubleshooting 91
- RAID Guidelines 92
- 007-4522-003 77 93
- 78 007-4522-003 94
- 7 address ranges 97
- 82 007-4522-003 98
- PSU good LED 100
- DC ouput fail LED 100
- AC input fail LED 100
- Fan fail LED 100
- RAID LRC I/O Module LEDs 101
- Expansion 103
- JBOD LRC I/O Module LEDs 105
- Drive Carrier Module LEDs 106
- present 107
- Thermal Control 108
- Using Test Mode 109
- 94 007-4522-003 110
- 5: Troubleshooting 110
- Adding a Drive Carrier Module 111
- Torx screwdriver 112
- 007-4522-003 99 115
- A. Technical Specifications 119
- Component Weight 120
- Specification Value 120
- Environmental Requirements 121
- Power Requirements 122
- LRC I/O Module Specifications 123
- Factor Requirement 124
- B. Regulatory Information 125
- Attention 126
- VCCI Class 1 Statement 126
- Class A Warning for Taiwan 127
- 114 007-4522-003 130
- 116 007-4522-003 132
- 118 007-4522-003 134
Produits connexes et manuels pour Mise en réseau AcQuisition Technology Quad M-module Carrier i4000
(20 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.136 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels